ENGINEERING

• The Heusinkveld Sim Shifter Sequential is a durable and compact sequential shifter system, which allows it to be installed in the tightest simulator environments.
• It has specifically been designed to mimic short throw sequential shifters. These can often be found in junior formula racing cars.
• Using a ball spring resistance system, shifting requires an early peak force after which resistance drops. This simulates the feeling as if your gearbox slides into the next or previous gear when the lever is engaged.
• The shifter is fitted with soft end-stops for the lever, resulting in a relative low amount of noise when shifting through gears.

The post Heusinkveld Sim Shifter Sequential appeared first on Simulation1Systems.

Sideways fun

Ideal for rally and drifting, the all-new ClubSport Handbrake V2 is a huge step forward in performance and durability with stronger components and improved electronics.

 

All-new design

The cast and CNC-finished metal construction has been totally redesigned to be stronger and more robust. Ball bearings on the pivot point create a smooth and consistent feel.

Smooth analogue input

Equipped with a precision load cell sensor, the ClubSport Handbrake V2 delivers smooth, consistent analogue input. The RJ12 connection always ensures a stable signal.

Adjustable preload.

Simply open the casing for quick access to the preload adjustment disc. By adding more preload, you create more tension on the elastomer and load cell stack, increasing the initial resistance on the lever.

Adjustable angle and travel

Three mounting positions on the lever allow for large angle changes, along with a rear bolt assembly for fine-tuning. The hand-removable spacer can be placed in two orientations, allowing a quick change between three travel settings.

Side-mount

The ClubSport Handbrake V2 is designed to mount to the side of a ClubSport Shifter (sold separately) with the included spacer.

Angle mount

Mounting slots instead of holes allows the handbrake to be angled slightly towards the driver, which can be more comfortable.

The post Fanatec ClubSport Handbrake V2 appeared first on Simulation1Systems.

The shifter has undergone 100’s of hours of live testing, weighing 3.5kg, the Bazooka is built to undergo the stresses you’d expect on track.

Over 40 years of engineering and racecraft has brought us to this development. BDH Race Simulator products are Designed and Built in York, England. Accuracy, Endurance, Authenticity and Power are all hallmarks of our products, raced all over the world.

The post BDH H1 H Pattern Shifter appeared first on Simulation1Systems.

Material

One big differentiator of our gear shifters to the current market is the material. In a market where plastic products have dominated, people often think ‘metal’ is considered the hardest or toughest material that could be used. For us just any old metal is not enough. We use the highest quality steel 835M19 often found in aerospace applications and go one step further to apply heat treatment to case harden the material. Once the material has been hardened only the most specialised carbide/diamond tools can be used to perforate it. We do this for ultimate durability on all the critical components, creating a shifter designed to last a lifetime.. We are using the same electronics which is a Leo Bodnar board with magnetic switches to sense the gear shifts for the ultimate reliability.

The post Pro-Sim PSL Sequential Shifter V2 appeared first on Simulation1Systems.

This shifter can be directly bolted underneath using 4 M6 bolts or alternatively you can bolt our attachment plate to the shifter and bolt through the 4 holes from the top into your setup

Material

One big differentiator of our gear shifters to the current market is the material. In a market where plastic products have dominated, people often think ‘metal’ is considered the hardest or toughest material that could be used. For us just any old metal is not enough. We use the highest quality steel 835M19 often found in aerospace applications and go one step further to apply heat treatment to case harden the material. Once the material has been hardened only the most specialised carbide/diamond tools can be used to perforate it. We do this for ultimate durability on all the critical components, creating a shifter designed to last a lifetime.

Hydraulic shift lock mechanism explained (Optional Extra can be retro fitted)

The main problem with all shifters on the market at the moment is that you cannot simulate missed gears nor have any interaction with the software. For this to be accurate it also needs to simulate the different type of gearboxes for dog engagement and also synchromesh:

Synchromesh

A synchromesh gearbox is what you would commonly find in your road car. This type of gear is engaged using cones to match the speed of the gears and then held in place with multiple ‘teeth’. With this type of gearbox there is virtually no play when in gear but there is a lot of surface area with load on holding the gear in place. Because of the load on the teeth and the fact there is not much space the gear needs to be doing almost exactly the same speeds to be able to engage and this is what the cones do but they cannot overcome the engine brake without doing damage to the gearbox and so the clutch is needed for all changes.

Dog engagement

A dog engagement box is what you will commonly find in race cars and on most sequential gearboxes. This type of gear usually has 3 to 6 ‘dogs’ on each gear and there is a lot of free space for them to engage this means there is normally quite a lot of play when in gear and why you often see race cars juddering forward and backwards when going down the pitlane. When you are driving fast this is not an issue as you are pushing on one side of the dog for acceleration or braking rather than hovering in the middle, this is also why they are not suitable for daily use on the road.

When shifting gears because of the space between the gears normally there can be up to a 900rpm difference in gear speeds and the gear will still go in, because of this you do not need the clutch. To make a gear change you need to reduce the load on the dogs so that it can released, this is normally done by just lifting the throttle on the up change. To change down a gear there is already a reduction in load that is sufficient you just need to blip the throttle so that you do not lock the rear wheels or cause unnecessary wear on the gearbox.

The post Pro-Sim Sequential Shifter appeared first on Simulation1Systems.

The feeling is exactly the same as the real car and when you change gear and you can also see the selector rods engaging behind the Perspex cover exactly like your real gearbox would. The design and concept is taken directly from a production Quaife H pattern gearbox. On our shifter the feeling comes from the selector rods and the centralization device used on most gearboxes rather than relying on a gate plate at the top which is what all other shifters on the market currently do.

The shifter itself is fully adjustable with the force of both centering and going through the gate easily adjustable by the user. The pivot point of the gear lever is also adjustable meaning without changing the length of the lever you can adjust the through between gears. The shifter has a short gear lever as standard which is something similar to one found on a Caterham and by the use of our shaft extension you have an additional 150mm possible in height and this is adjustable by 70mm to any height required.

The shifter will have a USB B socket on the back to be connected directly to the PC as a stand-alone device, we will supply the shifter with a high quality 2m USB A to B cable.

Material

One big differentiator of this gear shifter to the current market is the material. In a market where plastic products have dominated, people often think ‘metal’ is considered the hardest or toughest material that could be used. For us just any old metal is not enough. They use the highest quality steel 835M19 often found in aerospace applications and go one step further to apply heat treatment to case harden the material. Once the material has been hardened only the most specialised carbide/diamond tools can be used to perforate it. We do this for ultimate durability on all the critical components, creating a shifter designed to last a lifetime.

The proof can be seen in the longevity of our products with the first being produced in 2017 and not having a single breakage to date, even with several 1000 made in total and counting.

Hydraulic shift lock mechanism explained (Optional Extra can be retro fitted)

The main problem with all shifters on the market at the moment is that you cannot simulate missed gears nor have any interaction with the software. For this to be accurate it also needs to simulate the different type of gearboxes for dog engagement and also synchromesh:

Synchromesh

A synchromesh gearbox is what you would commonly find in your road car. This type of gear is engaged using cones to match the speed of the gears and then held in place with multiple ‘teeth’. With this type of gearbox there is virtually no play when in gear but there is a lot of surface area with load on holding the gear in place. Because of the load on the teeth and the fact there is not much space the gear needs to be doing almost exactly the same speeds to be able to engage and this is what the cones do but they cannot overcome the engine brake without doing damage to the gearbox and so the clutch is needed for all changes.

Dog engagement

A dog engagement box is what you will commonly find in race cars and on most sequential gearboxes. This type of gear usually has 3 to 6 ‘dogs’ on each gear and there is a lot of free space for them to engage this means there is normally quite a lot of play when in gear and why you often see race cars juddering forward and backwards when going down the pitlane. When you are driving fast this is not an issue as you are pushing on one side of the dog for acceleration or braking rather than hovering in the middle, this is also why they are not suitable for daily use on the road.

When shifting gears because of the space between the gears normally there can be up to a 900rpm difference in gear speeds and the gear will still go in, because of this you do not need the clutch. To make a gear change you need to reduce the load on the dogs so that it can released, this is normally done by just lifting the throttle on the up change. To change down a gear there is already a reduction in load that is sufficient you just need to blip the throttle so that you do not lock the rear wheels or cause unnecessary wear on the gearbox.

The post Pro-Sim H Pattern Shifter appeared first on Simulation1Systems.

H-Shifter for PC

FREX Hshift+ 6 Speed+R

-Feel pleasure every time you engage the gear.
-Realistic stick shift feeling not a switch box like others.

The post FREX Hshift+ appeared first on Simulation1Systems.

The post Aiologs Handbrake appeared first on Simulation1Systems.

The post Aiologs Shifter Sequential appeared first on Simulation1Systems.

Over 4 years of development, Aiologs has built 6 prototypes, tried 10 conceptual mechanical principles in different parts of the device and created a unique solution with 4 ways to adjust your shifting experience.
The Y-axis (Forward – Backward) and X-axis (Left – Right) springs are pushed by mechanisms that adjust spring compression to create unique tension chart.
The Y-axis has 2 separate modulators to create at least 3 tension types of shifting (Y1, Y2, Y1+Y2)
Shifting to Reverse and 7th speed is performed under additional pressure.

Adjustments

– Y-axis tension
– X-axis tension
– Y-axis progression types: Sharp, Smooth
– Knob installation height: 180–400mm

Features

– Full steel mechanical core allowed us to make a compact and powerful device.
– With dimensions of 86x86x136mm, it is the most compact solution between hight-level H-Shifters on the market.
– Stainless steel box contains round tempered glasses and adjustable RGB lightning.
– Shifts are precisely detected by magnetic contactless sensors.
– The polished aluminum handle comes with 3 stainless steel rods of varying lengths by default.
– A variety of mounting options make it easy to attach the device to any rig or desktop.
– Device (HID Joystick) is working on Windows PCs via USB and is compatible with drive, race, truck and etc simulators.

The post Aiologs H-pattern Shifter appeared first on Simulation1Systems.